Recovery Tank Lid

From a Bolted Acrylic Lid to a Two-Piece Molded Lid: About 75% Lower Cost

A floor cleaning equipment manufacturer was building the recovery tank lid on one of its machines from laser-cut acrylic, a sheet-rubber hinge and latch, and ten sets of bolts, washers and nuts, with four holes drilled in the tank for every machine and the parts coming from several suppliers. FormRep replaced it with a two-piece design: an injection-molded clear polycarbonate lid and a tether. The new lid costs about 75% less, installs in about 30 seconds instead of five minutes with no drilling, and paid back its tooling investment within a matter of months.

2 partsLid and tether
~75%Lower cost
5 min → 30 sAssembly time
MonthsTooling payback
  • Customer: Floor cleaning equipment manufacturer
  • Part: Clear lid for the recovery tank on a floor cleaning machine
  • Starting point: Laser-cut acrylic (PMMA) lid with a sheet-rubber hinge and latch, fastened with 10 sets of bolts, washers and nuts through 4 holes drilled in the tank
  • Material: Clear polycarbonate (PC), injection molded
  • Results: Two parts instead of a kit of hardware, no holes to drill in the tank, about 75% lower cost, assembly cut from 5 minutes to 30 seconds, tooling paid back within months

The challenge

The original lid was a flat piece of laser-cut acrylic. A strip of sheet rubber served as the hinge and another piece as the latch, and both were held on with ten sets of bolts, washers and nuts that fastened the hinge to the tank and the lid and attached the latch. Four holes had to be drilled in every tank just to mount it. Every lid meant a stack of separate components to buy from multiple suppliers, keep in stock and put together by hand, plus a drilling step on the tank, at about five minutes of assembly per lid.

Original recovery tank lid: laser-cut acrylic with a bolted sheet-rubber hinge and latch
Before: laser-cut acrylic with a bolted rubber hinge and latch.
Two-piece injection-molded clear polycarbonate recovery tank lid with tether
After: a molded polycarbonate lid and a tether. No hardware.

Designing the hardware out

Instead of copying the flat acrylic panel, we designed the lid around what it has to do: seal the tank and hold up to the vacuum the machine pulls on it, stay attached to the machine and come off quickly when the operator needs to get in. The result is a two-piece design that replaces the panel, the rubber hinge, the latch and all of the fasteners.

  • Two parts instead of a kit. A molded lid and a tether keep the lid with the machine. No rubber hinge, no latch and no bolts.
  • Built for vacuum. The recovery tank runs under the vacuum the machine generates, so the molded lid was designed to withstand those forces without deforming or pulling loose.
  • Clear polycarbonate. The lid stays transparent like the acrylic it replaced, so the tank can still be checked at a glance, in a material that is tougher than acrylic.
  • Nothing to drill or bolt. The four mounting holes the old lid needed in every tank are gone, and with no hardware to fasten, assembly dropped from about five minutes to about 30 seconds.
  • One source instead of several. The lid comes from a single supplier, ready to install.

Results

Before After
Parts Acrylic panel, sheet-rubber hinge and latch, 10 sets of bolts, washers and nuts 2: molded lid and tether
Material Laser-cut acrylic (PMMA) Injection-molded clear polycarbonate (PC)
Holes drilled in the tank 4 per machine None
Suppliers Several One
Assembly time About 5 minutes About 30 seconds
Cost Baseline About 75% lower
Tooling payback n/a Within months

Why it matters

Many parts start life as a flat panel with purchased hardware bolted on because that was the fastest way to get the first machines out the door. Once volumes settle, a molded design can often do the same job with a fraction of the parts, cost less and go together in seconds. FormRep handles it start to finish: design, printed prototypes, tooling and injection molding, with no minimum run.

See more made-to-fit solutions, or read how a 23-part cart bracket became 6 parts.

Have a part held together with bolts and brackets?
Request a quote →

Secret Link